 |
Dimensions of End Caps MSS SP-75 |
| NPS D |
DN D |
OD D |
Length H |
Length H* |
| 16 | 400 | 406.4 | 178 | 203 |
| 18 | 450 | 457 | 203 | 229 |
| 20 | 500 | 508 | 229 | 254 |
| 22 | 550 | 559 | 254 | 279 |
| 24 | 600 | 610 | 267 | 305 |
| 26 | 650 | 660 | 267 | 305 |
| 28 | 700 | 711 | 267 | 305 |
| 30 | 750 | 762 | 267 | 305 |
| 32 | 800 | 813 | 267 | 305 |
| 34 | 850 | 864 | 267 | 305 |
| 36 | 900 | 914 | 267 | 305 |
| 38 | 950 | 965 | 305 | 343 |
| 40 | 1000 | 1016 | 305 | 343 |
| 42 | 1050 | 1067 | 305 | 343 |
| 44 | 1100 | 1118 | 343 | 381 |
| 46 | 1150 | 1168 | 343 | 381 |
| 48 | 1200 | 1219 | 343 | 381 |
| 50 | 1250 | 1270 | 368 | 406 |
| 52 | 1300 | 1321 | 368 | 406 |
| 54 | 1350 | 1372 | 406 | 445 |
| 56 | 1400 | 1422 | 406 | 445 |
| 58 | 1450 | 1473 | 419 | 457 |
| 60 | 1500 | 1524 | 419 | 457 |
- Dimensions are in millimeters unless otherwise indicated
- Wall thickness (t) must be specified by customer
- For (t) greater than 1.0 inch, caps may be furnished to length H*, at option of manufacturer
- The shape of these caps shall be ellipsoidal and shall conform to the shape requirements as given in the ASME BPVC
Dimensional Tolerances MSS SP-75
| NPS | Inside Diameter at End | Out of Roundness | ||
| At Ends of Fittings | Throughout body of Elbows | |||
| Elbows | Other | |||
| 16-24 | ±2.29 | 4.83 | 3.05 | 2.5% |
| 26-36 | ±2.29 | *A | 3.05 | 2.5% |
| 38-48 | ±3.05 | *A | 3.05 | 2.5% |
| 50-60 | ±6.35 | *A | 3.05 | 2.5% |
| NPS | 90°-45° Elbows LR Cte |
Tees Cte |
Reducers Length |
Caps Length |
| 16-24 | ±2.29 | ±2.29 | ±2.29 | ±6.35 |
| 26-36 | ±3.05 | ±3.05 | ±4.83 | ±9.65 |
| 38-48 | ±4.83 | ±4.83 | ±9.65 | ±9.65 |
| 50-60 | ±6.35 | ±6.35 | ±9.65 | ±9.65 |
| NPS | Angularity off Angle Q | Elbows Off Plane P | Eccentric and Concentric Reducers Off Plane *B |
| 16-24 | 2.29 | 6.35 | 2.5% |
| 26-36 | 2.29 | 12.70 | 2.5% |
| 38-48 | 3.05 | 19.05 | 2.5% |
| 50-60 | 4.80 | 19.05 | 2.5% |
Dimensional tolerances are in millimeters unless otherwise indicated
