 |
Dimensions butt welded Stub Ends SCH 10S type A/B |
| NPS | OD | T | G | F | R Type A |
R Type B |
| 1/2 | 21.3 | 2.11 | 34.9 | 50.8 | 3.05 | 0.76 |
| 3/4 | 26.7 | 2.11 | 42.9 | 50.8 | 3.05 | 0.76 |
| 1 | 33.4 | 2.77 | 50.8 | 50.8 | 3.05 | 0.76 |
| 1.1/4 | 42.2 | 2.77 | 63.5 | 50.8 | 4.83 | 0.76 |
| 1.1/2 | 48.3 | 2.77 | 73 | 50.8 | 6.35 | 0.76 |
| 2 | 60.3 | 2.77 | 92.1 | 63.5 | 7.87 | 0.76 |
| 2.1/2 | 73 | 3.05 | 104.8 | 63.5 | 7.87 | 0.76 |
| 3 | 88.9 | 3.05 | 127 | 63.5 | 9.65 | 0.76 |
| 3.1/2 | 101.6 | 3.05 | 139.7 | 76.2 | 9.65 | 0.76 |
| 4 | 114.3 | 3.05 | 157.2 | 76.2 | 11.18 | 0.76 |
| 5 | 141.3 | 3.40 | 185.7 | 76.2 | 11.18 | 1.52 |
| 6 | 168.3 | 3.40 | 215.9 | 88.9 | 12.7 | 1.52 |
| 8 | 219.1 | 3.76 | 269.9 | 101.6 | 12.7 | 1.52 |
| 10 | 273.1 | 4.19 | 323.9 | 127 | 12.7 | 1.52 |
| 12 | 323.9 | 4.57 | 381 | 152.4 | 12.7 | 1.52 |
| 14 | 355.6 | 4.78 | 412.8 | 152.4 | 12.70 | 1.52 |
| 16 | 406.4 | 4.78 | 469.9 | 152.4 | 12.7 | 1.52 |
| 18 | 457.2 | 4.78 | 533.4 | 152.4 | 12.70 | 1.52 |
| 20 | 508 | 5.54 | 584.2 | 152.4 | 12.70 | 1.52 |
| 24 | 609.6 | 6.35 | 692.2 | 152.4 | 12.7 | 1.52 |
Dimensions are in millimeters unless otherwise indicated. Weights are in kilograms and approximately given.
Dimensional Tolerances Stub Ends MSS SP-43
| NPS | 1/2 to 2.1/2 | 3 to 3.1/2 | 4 | 5 to 8 | 10 to 18 | 20 to 24 |
| Outside Dia. at Welding End (OD) |
0.8 | 0.8 | 0.8 | + 1.6 - 0.8 |
+ 2.29 - 0.76 |
+ 3.05 - 0.76 |
| Overall Length (F) |
1.6 | 1.6 | 1.6 | 1.6 | 2 | 2 |
| Outside Dia. of Lap (G) |
+ 0 - 0.76 |
+ 0 - 0.76 |
+ 0 - 0.76 |
+ 0 - 0.76 |
+ 0 - 1.6 |
+ 0 - 1.6 |
| Thickness of Lap (T) |
+ 1.52 - 0 |
+ 1.52 - 0 |
+ 1.52 - 0 |
+ 1.52 - 0 |
+ 1.52 - 0 |
+ 1.52 - 0 |
| Fillet Radius of Lap (R) |
+ 0 - 0.76 |
+ 0 - 0.76 |
+ 0 - 1.6 |
+ 0 - 1.6 |
+ 0 - 1.6 |
+ 0 - 1.6 |
| Wall Thickness (t) |
Not less than 87.5% of Nominal Wall Thickness | |||||
Dimensional tolerances are in millimeters unless otherwise indicated.
Notes..
- Type A for Lap Joint Flanges
- Type B for Slip On Flanges
- MSS SP-43 only covers stainless steel buttweld fittings made for use with Schedule 5S and 10S pipe and Stub Ends suitable for use with Schedule 40S pipe, as defined in ASME B36.19. The dimensions and dimensional tolerances defined in MSS SP-43 are substantially the same as those in ASME B16.9 specifications from NPS 1/2 - NPS 24. Except with regard to the outside diameter at the bevel.
Related Post(s)
Lap Joint Flange with Stub End
A Stub End always will be used with a Lap Joint flange, as a backing flange. This flange connections are applied, in low-pressure and non critical applications...
A Stub End always will be used with a Lap Joint flange, as a backing flange. This flange connections are applied, in low-pressure and non critical applications...
