 |
Dimensions Lap Joint Flanges & Stud Bolts ASME B16.5 |
| OTHER DIA | NPS 1.1/4 ID=43.7 r=5 | |||||
| CLass | 150 | 300 | 600 | 900 | 1500 | 2500 |
| DIA A | 59 | 64 | 64 | 64 | 64 | 73 |
| DIA D | 115 | 135 | 135 | 160 | 160 | 185 |
| THK B | 15.9 | 19.1 | 20.7 | 28.6 | 28.6 | 38.1 |
| DIA K | 88.9 | 98.4 | 98.4 | 111.1 | 111.1 | 130.2 |
| H | 21 | 27 | 29 | 41 | 41 | 52 |
| NO. L | 4 | 4 | 4 | 4 | 4 | 4 |
| DIA L | 15.9 | 19.1 | 19.1 | 25.4 | 25.4 | 28.6 |
| Stud Bolts Diameter x Length | ||||||
| DIA (in) | 1/2 | 5/8 | 5/8 | 7/8 | 7/8 | 1 |
| lgth (mm) | 70 | 85 | 95 | 125 | 125 | 150 |
Notes..
- Dimensions are in millimeters unless otherwise indicated.
- The length of the Stud Bolt does not include the height of the chamfers (points).
- The length of the Stud Bolts includes one Spiral Wound Gasket with a 4.5mm thick sealing element, which is compressed to 3mm while tightening the Raised Face flange connection.
- Important! please read this short article
Dimensional Tolerances of Lap Joint Flanges ASME B16.5
Outside Diameter *
Tolerances not listed in ASME B16.5 2013
≤ 24 = 1.6 mm
> 24 = ± 3.2 mm
Tolerances not listed in ASME B16.5 2013
≤ 24 = 1.6 mm
> 24 = ± 3.2 mm
Inside Diameter
≤ 10 = ± 0.8 mm
≥ 12 = + 1.6 mm / - 0 mm
≤ 10 = ± 0.8 mm
≥ 12 = + 1.6 mm / - 0 mm
Outside Diameter of Hub
≤ 12 = + 2.4 mm / - 1.6 mm
≥ 14 = ± 3.2 mm
≤ 12 = + 2.4 mm / - 1.6 mm
≥ 14 = ± 3.2 mm
Diameter of Counterbore
Same as for Inside Diameter
Same as for Inside Diameter
Drilling
Bolt Circle = 1.6 mm
Bolt Hole Spacing = ± 0.8 mm
Bolt Circle = 1.6 mm
Bolt Hole Spacing = ± 0.8 mm
Eccentricity of Bolt Circle
≤ 2.1/2 = 0.8 mm max.
≥ 3 = 1.6 mm max.
≤ 2.1/2 = 0.8 mm max.
≥ 3 = 1.6 mm max.
Thickness
≤ 18 = + 3.2 mm / - 0
≥ 20 = + 4.8 mm / - 0
≤ 18 = + 3.2 mm / - 0
≥ 20 = + 4.8 mm / - 0
Length thru Hub
≤ 18 = + 3.2 mm / - 0.8 mm
≥ 20 = + 4.8 mm / - 1.6 mm
≤ 18 = + 3.2 mm / - 0.8 mm
≥ 20 = + 4.8 mm / - 1.6 mm
Diameter of Contact Face
1.6 mm Raised Face = ± 0.8 mm
6.35 mm Raised Face
Tongue and Groove / Male-Female
± 0.4 mm
1.6 mm Raised Face = ± 0.8 mm
6.35 mm Raised Face
Tongue and Groove / Male-Female
± 0.4 mm
Studs are measured parallel to the axis (L) from the first to the thread without the chamfers (points). S = free threads equals 1/3 time bolt dia
Hex bolts are measured from under the head to the end of the bolt
Related Post(s)
Flange Face Finish
The ASME B16.5 code requires that the flange face has a specific roughness to ensure that this surface be compatible with the gasket...
The ASME B16.5 code requires that the flange face has a specific roughness to ensure that this surface be compatible with the gasket...
